Integrated stepper motor MIS340 available with hollow shaft
Order Order History Filter by Component Controller Driver Encoder Motor Overall Length 2.3" 2.4" 2 1/2" 2.6" 2.8" 3" 3.3" 3.7" 3.8" 3.9" 4.2" 4.3" 4.7" 5.1" 346 mm 356 mm 446 mm 456 mm 546 mm 556 mm 656 mm 756 mm 862 mm Step Resolution 1/256 1/128 1/125
Integrated Stepper Motor Driver 38A 1240VDC
TI's DRV8462 is a 65-V, 10-A, dual H-bridge stepper motor driver with smart tune, stall detect and auto-torque. Find parameters, ordering and quality information
Integrated Stepper Motor Driver 02A 1028VDC for NEMA 8,11,14,17 Stepper Motor
Integrated Stepper Motors Integrated Step-Servo Motors Integrated Servo Motors - MDX+ Series NEW Stepper Drives & Motors Stepper Drives - STF Series NEW AM Series Stepper Motors NEW
Integrated Stepper Motor Driver 38A 1240VDC
The DRV8846 provides a highly-integrated stepper motor driver for cameras, printers, projectors, and other automated equipment applications. The device has two H-bridges and a microstepping indexer and is intended to drive a bipolar stepper motor. The output block of each H-bridge driver consists of N-channel and P-channel power MOSFETs.
Integrated stepper motor MIS340 available with hollow shaft
Integrated Stepper Motors, drivers and controllers are available in NEMA sizes 17 and 23, with torque ratings from 31 to 425 ounce inches. High torque stepper motors are used in the Integrated Stepper Motor series offer 1.8 degree step angle with stack lengths of 1/2, 1, 2, or 3, providing for a wide range of start-up torque and intertia.
STEPPER MOTOR DRIVER Controller Integrated Board Speed Angle Control Module PLC 29.98 PicClick
STM integrated drive+motors fuse step motor and drive components into a single device. These integrated steppers offer a space-saving design that reduces wiring and saves on cost over separate motor and drive components. STM integrated steppers, in NEMA 17, 23, and 24 frame sizes, combine the best of Applied Motion's drive and motor offering in a single, integrated device.
CNC NEMA 23 Integrated Stepper Motor with driver DIP switches 57 HS stepper motor with low
The integrated drive/motor units combine accurate position and speed control with microstepping to smooth motion and step response. E models include encoders. Advanced R models include indexer, communications options and more. Single Shaft Stepper Motors IP65 Stepper Motors Dual Shaft and Encoder Stepper Motors Stepper Motor Linear Actuators
MAC Integrated Servo Motors and Industrial Motor from JVL
Description Technical data Size 1.1 in Holding Torque 12.7 oz-in - 25.5 oz-in Operating Voltage 12 VDC - 30 VDC Encoder Type single-turn absolute Interface - Fieldbus CANopen, Modbus RTU PD2-C - Stepper motor with integrated controller - NEMA 17 Description Technical data Size 1.7 in Holding Torque 70.8 oz-in Operating Voltage 12 VDC - 48 VDC
Integrated Stepper Motor Driver 38A 1240VDC for NEMA 23,24,34
Get smooth, effortless motion with our broad portfolio of highly-integrated stepper motor drivers that feature automatic tuning, accurate current sensing and advanced diagnostics. Scaling across a wide voltage and current range, our portfolio is suited for a variety of industrial and automotive applications.
CDA Integrated stepper motors
AMCI's SD17060E-K Integrated stepper motor controller/driver is rated for 6.0 amp RMS or 8.5 amp Peak. Programmable to any value between 200 and 32,767 steps per revolution. The SD17060E-K Integrated Drive uses variable step size motion for extreme smoothness regardless of programmed resolution.
Integrated Stepper Motor & Controllers with CANbus
TI's DRV8434 is a 48-V, 2.5-A bipolar stepper motor driver with integrated current sensing and 1/256 microstepping. Find parameters, ordering and quality information
Integrated Stepper Motors Arcus Technology, Inc.
Stepper Motors with Integrated Motion Control With a built-in controller and driver, these stepper motors come ready to program and operate. After connecting to a computer for initial setup, the controller can store and run programs on its own.
Miniature Integrated Stepper Motor Driver Controller CANopen Bus Small Volume PMC007 CQPUSI
This integrated motor driver makes interfacing with a microcontroller super easy as you only need two pins to control both the speed and the direction of the stepper motor. The driver has a maximum output capacity of 35 V and ± 2 A which is great for driving small to medium-sized stepper motors like a NEMA 17 bipolar stepper motor.
INTEGRATED STEPPER MOTOR Driver Controller Touch Screen Modbusrtu485 Version 49.13 PicClick
integrated stepper motors Starting with our proven stepper motors, we added a driver, controller, and encoder to create an all-in-one convenient motion control solution. This helps to save space as everything is compactly integrated into one motor.
Stepper motor driver controller micro integrated 57 motor integrated installation rs485 bus
SureStep DC integrated stepper motor/drive, microstepping, NEMA 17 frame, IP20, 2A, 12-48 VDC, bipolar, 68 oz-in holding torque, 1.8-degree step angle, 200 to 25000 steps per revolution. Stride Interactive Product Tour Request Form
Integrated Stepper Motor Driver 1.54A 1240VDC for NEMA 17,23,24 Stepper Motor
Drivers and Controllers for Stepper Motors | McMaster-Carr (562) 692-5911 Email Us Filter by Component Controller Driver Number of Outputs 3 4 Overall Height 0.8" 0.9" 1.3" 1 3/4" 2.1" Step Resolution Maximum Temperature 100° F 130° F 185° F Overall Length Number of Step Resolution Settings Housing Material Serial Port Interface RS-232 RS-485
